10 Sites To Help Become An Expert In Repair Car Keys

How to Repair Car Keys

Car keys may seem tiny and insignificant, however they are crucial to the operation of your vehicle. Replacing a traditional key or a modern transponder key can cost upwards of $200.

There are methods to fix your car keys at home with a fraction of the cost. This article will cover the most frequently encountered car keys issues and the DIY solutions.

Dead Key Fob Batteries

Cars are equipped with a remote key fob that makes opening the doors, trunk and tailgate easier than ever. However, the battery in this device can die. There are a few strategies you can employ to fix this problem quickly.

First, check if the car is still in ignition mode. If so the battery on the key fob could be low rather than dead. To test this, push the button on the key fob towards the ignition button. If this does not work, the battery is probably fine and only has to be replaced.

To replace the fob's battery, start by prying open the case with the help of a screwdriver or watch-type device. Do not apply too much force since this could cause the fob's case to split. If the fob isn't opening, try using your pry tool several times around the outside of the case.

After the fob has been opened then remove the mechanical key and then open the electronic section of the car. Install  key repair car  and snap it back into the shell. If your key fob isn't working after this procedure, it could be that there is an problem with the remote starting system in your car. This will require an expert to determine the cause. A reputable mechanic will able help you in this situation. You can also call roadside assistance for assistance with your vehicle, if you require it.

Broken Key Ring

If your key fob isn't working because the ring is broken there are a few options you can try. First, you should check to see if the broken piece is still inside the ignition. If it's still in there it, remove it without damaging the ignition lock or the door lock. If you are having trouble removing it, call a locksmith for help. They have special tools to safely remove a damaged or broken key from the ignition.

Another reason for a broken car key is corrosion on the circuit board or frame. You can clean the circuit board using cotton swab. This will remove corrosion and ensure that the contact pads aren't damaged.

Repair a damaged ring using a strong wire or nail to seal the hole. Superglue can also be used to repair a broken ring. After cleaning the ring with a moist cloth Apply a small amount superglue on each end of the nail or wire. Then, press the pieces together and allow them to dry before using your vehicle. These DIY solutions can seem appealing, but they're really just an interim measure. For long-term repairs, it's recommended to work with an experienced locksmith. They have the expertise and tools to fix damaged keys quickly and efficiently. They can replace the battery and reprogram your key fob, if needed.

Broken Key Blade

Some key blades may break due to wear and tear. If this happens, you should probably buy a new one. Luckily, this problem isn't as serious as it may appear at first glance. The primary issue is that the blade snapped off the case.

Spraying lubricant into the keyhole is a solution to fix the problem. You can then make use of pliers or tweezers grasp the damaged end of the key and pull it. If the key is magnetic, you can also use a magnet to help pull it out. Use a magnet as a aid to you remove the key, but be careful to not break the lock tumbler.

If you're unable to remove the broken piece from the key, contact a locksmith right away. They're equipped with special tools that can safely remove keys without causing any further damage.

You can also use super glue to fix a snapped key. Apply a small amount of the glue to the edges and press them together. Wait until the glue has dried before inserting your key into the lock. This method isn't very reliable, and you might have to repeat it a few times before it is successful. Super glue might not be able to hold the key in place. This is more of a temporary fix than a permanent one.

Broken Plastic Loop

If the loop of plastic on your key fob fails it can make the key ineffective. It's a fairly simple fix. To replace it alternative, you can use an extremely thick wire or a finishing nail. For each end of the wire or nail you need to drill two holes into the plastic loop. Cut the wire or nail to key width, then place tiny drops of superglue into each hole. Then, press the wire or nail into the holes and allow them to dry.

Another option is to get an alternative shell from a locksmith who sells them. They can take out the programmable component of your key, then transfer it to the new shell and cut a new blade for much less than a full replacement cost.

It's not the ideal solution, but it'll bring you back on the road in case your key split in half. It can be difficult to fix the blade of the key if it's in the ignition. You can try using hair clips, a needle or an extractor tool to pull the broken piece of the ignition, however this can be risky if not cautious. The best solution is to call a locksmith who has special tools for safely removing broken keys from the ignition. You can also request a new key that is made using the correct cuts for the ignition of your vehicle.

Broken Master Key

If a key gets damaged inside the lock, you'll have to find it before it is completely destroyed. There are a few techniques that you can try, such as using lubricants, tools, needle nose pliers or tweezers to pick up a piece of the damaged key and pull it out.

Spray the inside of the lock with WD-40 or graphite powder. You can also try the hacksaw blade method which involves carefully sliding the blade along the edge of the broken key, and attaching it to the 'teeth'. If you are able to do this you should be able pull out the broken key from the lock.

Another useful tool is an extractor for keys spiral, which you can find in a wide range of hardware stores. It's a thin and flexible bar with spiral threads, that can be inserted into the keyway and bent to get into the broken section of the key. Once it has hooked onto the serrations, you can twist it in a circular direction and lever it against the broken portion of the key to get it out.

It's worth trying to get rid of a broken master key before calling an expert locksmith. If you can't get the piece out, it's time to call in the big guns and let a locksmith make you a brand new key and reprogram it to the transponder of your car.